» Blocking Queries
Many endpoints in Consul support a feature known as "blocking queries". A blocking query is used to wait for a potential change using long polling. Not all endpoints support blocking, but each endpoint uniquely documents its support for blocking queries in the documentation.
Endpoints that support blocking queries return an HTTP header named
X-Consul-Index. This is a unique identifier representing the current state of
the requested resource.
On subsequent requests for this resource, the client can set the
string parameter to the value of
X-Consul-Index, indicating that the client
wishes to wait for any changes subsequent to that index.
When this is provided, the HTTP request will "hang" until a change in the system occurs, or the maximum timeout is reached. A critical note is that the return of a blocking request is no guarantee of a change. It is possible that the timeout was reached or that there was an idempotent write that does not affect the result of the query.
In addition to
index, endpoints that support blocking will also honor a
parameter specifying a maximum duration for the blocking request. This is
limited to 10 minutes. If not set, the wait time defaults to 5 minutes. This
value can be specified in the form of "10s" or "5m" (i.e., 10 seconds or 5
minutes, respectively). A small random amount of additional wait time is added
to the supplied maximum
wait time to spread out the wake up time of any
concurrent requests. This adds up to
wait / 16 additional time to the maximum
» Implementation Details
While the mechanism is relatively simple to work with, there are a few edge cases that must be handled correctly.
Reset the index if it goes backwards. While indexes in general are monotonically increasing(i.e. they should only ever increase as time passes), there are several real-world scenarios in which they can go backwards for a given query. Implementations must check to see if a returned index is lower than the previous value, and if it is, should reset index to
0- effectively restarting their blocking loop. Failure to do so may cause the client to miss future updates for an unbounded time, or to use an invalid index value that causes no blocking and increases load on the servers. Cases where this can occur include:
- If a raft snapshot is restored on the servers with older version of the data.
- KV list operations where an item with the highest index is removed.
- A Consul upgrade changes the way watches work to optimize them with more granular indexes.
Sanity check index is greater than zero. After the initial request (or a reset as above) the
X-Consul-Indexreturned should always be greater than zero. It is a bug in Consul if it is not, however this has happened a few times and can still be triggered on some older Consul versions. It's especially bad because it causes blocking clients that are not aware to enter a busy loop, using excessive client CPU and causing high load on servers. It is always safe to use an index of
1to wait for updates when the data being requested doesn't exist yet, so clients should sanity check that their index is at least 1 after each blocking response is handled to be sure they actually block on the next request.
Rate limit. The blocking query mechanism is reasonably efficient when updates are relatively rare (order of tens of seconds to minutes between updates). In cases where a result gets updated very fast however - possibly during an outage or incident with a badly behaved client - blocking query loops degrade into busy loops that consume excessive client CPU and cause high server load. While it's possible to just add a sleep to every iteration of the loop, this is not recommended since it causes update delivery to be delayed in the happy case, and it can exacerbate the problem since it increases the chance that the index has changed on the next request. Clients should instead rate limit the loop so that in the happy case they proceed without waiting, but when values start to churn quickly they degrade into polling at a reasonable rate (say every 15 seconds). Ideally this is done with an algorithm that allows a couple of quick successive deliveries before it starts to limit rate - a token bucket with burst of 2 is a simple way to achieve this.
» Hash-based Blocking Queries
A limited number of agent endpoints also support blocking however because the state is local to the agent and not managed with a consistent raft index, their blocking mechanism is different.
Since there is no monotonically increasing index, each response instead contains
X-Consul-ContentHash which is an opaque hash digest generated by
hashing over all fields in the response that are relevant.
Subsequent requests may be sent with a query parameter
value is the last hash header value seen, and this will block until the
timeout is passed or until the local agent's state changes in such a way that
the hash would be different.
Other than the different header and query parameter names, the biggest difference is that hash values are opaque and can't be compared to see if one result is older or newer than another. In general hash-based blocking will not return too early due to an idempotent update since the hash will remain the same unless the result actually changes, however as with index-based blocking there is no strict guarantee that clients will never observe the same result delivered before the full timeout has elapsed.